SparkFun IoT Starter Kit with Blynk Board

66.62 80.61€ VAT included
Rated 0/5 (0 Votes!)
Model: SPRKC-KIT-14682
Manufacturer: Sparkfun
Sparkfun

Blynk is an easy to use app builder that allows users to add a variety of buttons, sliders, graphical displays and even RGB controllers to their phone. The SparkFun Blynk Board is specially designed to work with the ?widgets? within the Blynk mobile app to create your next IoT project. Monitor local weather conditions, control LEDs from your phone, even send a tweet when it?s time to water your plants!

The SparkFun IoT Starter Kit with Blynk Board is a great way to gain a solid introduction to the world of Internet of Things (IoT) technology without any difficult programming. With this kit you will be able to get your Blynk Board connected and, by utilizing the pre-loaded projects, use diverse set of components to build an array of web- and phone-connected projects.

Every Blynk Board comes fully programmed and also includes a Blynk subscription code card (15k Energy at a $10 value), which will be needed to connect the Blynk Board to your Blynk account. Simply connect to a Wi-Fi signal and you are ready to use this starter kit! Getting started with your Blynk Board and getting it connected to the Blynk App on your iOS or Android device is a breeze. Once you?ve played with the ZeRGBa (a festively colored zebra 'widget' that can change the color of the on-board RGB LED) checkout our step-by-step project guide with detailed images on how to add and control the large selection of widgets within Blynk.

The kit does not require any soldering and is recommended for anyone with a drive to learn more about Blynk and its uses. So if you are looking for a new challenge or a way to get in on the IoT craze, check out the SparkFun IoT Starter Kit with Blynk Board!

Note: The Blynk app is compatible with iDevices running iOS 7.0+, and Android?s running any version above or equal to 4.0.

Includes:

Documents:

Examples:

  • Project 1: Blynk Button, Physical LED
  • Project 2: Physical Button, Blynk LED
  • Project 3: Slide-Dimming LEDs
  • Project 4: Temperature and Humidity Values
  • Project 5: Gauging the Analog-to-Digital Converter
  • Project 6: Automating With the Timer
  • Project 7: The LCD's Wealth of Information
  • Project 8: Joystick Joyride
  • Project 9: Graphing Voltage
  • Project 10: Charting Lighting History
  • Project 11: Terminal Chat
  • Project 12: BotaniTweeting
  • Project 13: Push Door, Push Phone
  • Project 14: Status Emails

Videos

For more information, please visit this products webpage.
More products in this category:

Buy Sparkfun On Demand »

More Featured Products
Force Sensitive Resistor Round
This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no ...
6.10€
Flex Sensor Sparkfun
A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of ...
7.95€
NodeMCU V3 IOT ESP8266 development kit
The NodeMcu is an open-source firmware and development kit that helps you to Prototype your IOT product within a few Lua script lines. Features: Open-source Interactive Programmable Low ...
5.75€
Ultrasonic Range Sensor HC-SR04
This is a non-contact distance measurement module. It’s designed for easy modular project usage with industrial performance. Features: - Detecting range: 2cm-4m - Best in 15 degree angle - 5VDC power supply - ...
2.13€
40 Pin Female-Female Splittable Jumper Wire 200mm
This is a splittable 40 pin 200mm length jumper wire for ...
2.87€
LilyPad Coin Cell Battery Holder - Switched - 20mm
Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you’ve even sewn a LilyPad slide switch in-line. Wouldn’t it be ...
2.23€
Pressure-Sensitive Conductive Sheet (Velostat/Linqstat)
This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit. It's pressure-sensitive: squeezing it will reduce the resistance, so it's handy for making flexible sensors. ...
4.96€
Europe Official Distributor
Adafruit
Pololu
Sparkfun
Makey makey
Lilypad
Arduino

Electan uses cookies for the operation of the website, monitoring site performance and to deliver interest based content.

Accept & Close

See privacy notice