Quadstepper Motor Driver Board

Referencia: SPRKC-ROB-10507
Fabricante: Sparkfun
Disponible: Descatalogado

Description: The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins. Each motor driver has an output drive capacity of 35V and 1Amps. The board is capable of driving motors in full, half, quarter, eight, and sixteenth-step modes. The logic levels are selectable between 3.3V and 5V by way of a jumper. The bus header allows you to control all four motors with only 6 IO pins by controlling the enable (EN pins) for each motor, although each motor will be activated alone, not simultaneously. Be sure to close all of the 'Bus Enable' jumpers on the back of the board in order to use the Bus header.

The Quadstepper is a great board for 3D printing applications as well as a host of other applications where it's necessary to control precise movement from logic level IO pins.

Note: Although this board can theoretically supply 2A per motor, you will run into heat issues if you do not have proper thermal management (ie - heatsinks). Without heatsinking, you can expect to drive each motor up to 1A, which would be fine for our stepper motors, or something similar.

Note: The Arduino Library currently only works with an Arduino Mega or Mega 2560.

Features:

  • Can control up to 4 bipolar stepper motors simultaneously.
  • Each motor driver has an output drive capacity of 8-35V and 2Amps.
  • Each channel uses potentiometers to control current to the motors.
  • Capable of driving motors in full, half, quarter, eight, and sixteenth-step modes.
  • Power input (barrel jack) needs to be less than 30V and supply enough current for your specific stepper motors.
  • Jumper (labeled "5V") controls power to the motor drivers, logic levels, and VOUT pin, selectable 3.3/5V.
  • Bus header allows you to control all four motors with only 6 IO pins by controlling the enable (EN pins) for each motor. Be sure to close the enable jumpers on the back of the board to use this feature.
  • 2.1mm, center positive barrel jack

Documents:

Para obtener más información, visite la página del producto.
Para ver otros productos en esta categoria:

 »

Otros productos que pueden ser de su interés

Makey Makey Original Classic

49.50€ 46.45€

El Makey Makey es un kit de creación interactiva que convierte prácticamente cualquier objeto común en diferentes teclas táctiles con lo que se puede ...

Portapilas CR2032 para Coser

3.87€ 1.94€

50% DESCUENTO SOLO hasta fin de existencias. Añade el producto al carro y aumentando la cantidad podrás ver cuantas unidades quedan ...

Cinta Adhesiva de Cobre 5mm

5.06€ 2.53€

Esta cinta de cobre permite variedad de aplicaciones, desde crear pistas para componentes electrónicos a fabricar antenas. Ancho 5mm. Longitud: 15m.50% DESCUENTO SOLO hasta fin de ...

Velostat Hoja Conductiva Sensible a la Presión - Linqstat

7.99€

El material conductivo velostat (o también conocido como Linqstat) es sensible a la presión, al doblarlo o arrugarlo disminuye su resistencia con lo que permite hacer sensores flexibles. Dimensiones 28 x ...

Kit Casa Inteligente para micro:bit Smart Home Kit

49.50€

Crea un hogar inteligente programando con micro:bit. Puedes usarlo para crear muchos proyectos diferentes, como un ventilador inteligente, luces activadas por voz, ventanas automáticas y más. Se adapta a la programación gráfica de ...

Robot Maqueen para Micro:bit DFRobot

37.93€

El Robot Maqueen para Micro:bit de DFRobot está diseñado específicamente para fomentar el interés de los niños en la ciencia y el pensamiento lógico a través de la educación STEM. ...

Robot Maqueen con Placa Micro:bit V2 Incluida

53.95€

Incluye La placa Micro:bit V2 y el robot Maqueen El Maqueen es un robot de programación ...

Copyright © 2006-2025 Electan Electrónica y Robótica
Electan
Tu Tienda Donde Comprar Micro:bit, Maqueen, Arduino y Robotica On Line. Todo lo que necesitas para tus proyectos a un click

Ubicacion: Elche, España

Teléfono: 966 410 250

E-Mail: info@electan.com