This is the Adafruit Feather M0 RFM69 Packet Radio (433 MHz). We call these RadioFruits, our take on an microcontroller with a RFM69 HCW packet radio transceiver plus built in USB and battery charging. Its an Adafruit Feather M0 with a 433MHz radio module cooked in!
Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.We have other boards in the Feather family, check'em out here.
This is the 433 MHz radio version. We also sell a 900 MHz version of the same radio chipset!
At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.
To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.
Here's some handy specs! Like all Feather M0's you get:
The Feather M0 Radio uses the extra space left over to add an RFM69HCW 433 or 900MHz radio module. These radios are not good for transmitting audio or video, but they do work quite well for small data packet transmission when you need more range than 2.4 GHz (BT, BLE, WiFi, ZigBee)
Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some headers so you can solder it in and plug into a solderless breadboard. You will need to cut and solder on a small piece of wire (any solid or stranded core is fine) in order to create your antenna. Lipoly battery and USB cable not included but we do have lots of options in the shop if you'd like!
El Arduino Starter Kit es el kit oficial de Arduino para realizar 15 proyectos de diferentes niveles de dificultad, incluye un manual en español y todos los componentes necesarios. Kit Arduino Original con Manual en ...
Varios colores. Longitud 30cm. 2 unidades de cada ...
Este portapilas esta diseñado específicamente para la placa BBC Micro:bit y tiene un cable de 150mm con el conector ...
Este kit incluye: Micro:bit V2 Cable USB corto Portapilas para 2 pilas AAA 2 pilas ...
El Robot Maqueen para Micro:bit de DFRobot está diseñado específicamente para fomentar el interés de los niños en la ciencia y el pensamiento lógico a través de la educación STEM. ...
Incluye: -Micro:bit V2 con BLE 5.0 Micrófono Altavoz y Acelerómetro -Funda Azul para Micro:bit V2 -Portapilas AAA con conector para micro:bit -Cable USB 2.0 Terminales ...
Incluye La placa Micro:bit V2 y el robot Maqueen El Maqueen es un robot de programación ...
Este mapa multifuncional de 120 x 90 cm está especialmente diseñado para aplicaciones de seguimiento de líneas. Hay líneas negras con una anchura de 2 cm impresas en el papel de mapa de 120 g, que es de alta calidad y no es fácil de ...