SparkFun LTE CAT M1/NB-IoT Shield - SARA-R4

87.56 105.95€ VAT included
Rated 0/5 (0 Votes!)
Model: SPRKC-CEL-14997
Manufacturer: Sparkfun
Sparkfun

The SparkFun LTE CAT M1/NB-IoT Shield equips your Arduino or Arduino-compatible microcontroller with access to data networks across the globe. This shield adds wireless, high-bandwidth cellular functionality to your IoT project while maintaining low power consumption and a small footprint. The SparkFun LTE CAT M1/NB-IoT Shield is based off the Arduino R3?s footprint that allows you to easily incorporate it with favorite Arduino-based device.

At the heart of the LTE Cat M1/NB-IoT shield is a u-blox SARA-R410M-02B LTE Cat M1/NB-IoT modem. Cat M1 (Category M1) and NB-IoT (Narrowband IoT) are both Low Power Wide Area Network (LPWAN) technologies that are designed to provide cellular communication to small IoT devices. They operate on LTE network bands just like most smartphones, and should be supported by most cellular network carriers. The u-blox SARA-R4 module communicates over a UART via a simple AT command set. We?ve provided a library to help you get started with everything from sending SMS text messages to communicating with servers over a TCP/IP connection. Additionally, both the module and library support an I2C GPS interface via a Qwiic connector, so you can plug in a u-blox GPS module and start remotely tracking your project.

Each SparkFun LTE CAT M1/NB-IoT Shield also includes a ceramic, Molex 1462000001 SMD antenna. The antenna has a gain of 3.8dBi around 1.7GHz to 2.7GHz. However, if you would prefer to use an external antenna, we have provided a U.FL connector that can be utilized by simply slicing through a jumper with a hobby knife.

Please be aware that there are a few extra parts required to get this shield fully functioning, other than an Arduino-based device. First, you'll need to supply your own SIM card, such as this one from Hologram (we do also offer this shield with an included one as well) and your own headers which will need to be soldered on.

Note: Be sure to check the Hardware Overview section in the Hookup Guide for compatible GPS modules. The onboard Qwiic connector is only designed to support u-blox-based GPS modules. It does not support any other GPS modules or sensors. We are continuing to add more modules so be sure to check back every so often to find out more!

Documents:

Videos

For more information, please visit this products webpage.
More products in this category:

Buy Sparkfun On Demand »

More Featured Products
Arduino Starter Kit Spanish Edition
Oficial Arduino Kit with 15 projects of different complexity. 1 Arduino Projects Book Spanish Edition (170 pages) 1 Arduino UNO board rev 3 1 USB cable 1 Breadboard 1 Easy-to-assemble wooden base 1 9v ...
82.60€ 65.08€
12.33€
Conductive Thread Bobbin - 12m (Smooth, Stainless Steel)
This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the ...
5.14€
Pressure-Sensitive Conductive Sheet (Velostat/Linqstat)
This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit. It's pressure-sensitive: squeezing it will reduce the resistance, so it's handy for making flexible sensors. ...
4.96€
Circuit Playground Express - Base Kit
It's the Circuit Playground Express Base Kit! It provides the few things you'll need to get started with the new Circuit Playground Express. This version of Circuit ...
32.80€
Europe Official Distributor
Adafruit
Pololu
Sparkfun
Makey makey
Lilypad
Arduino

Electan uses cookies for the operation of the website, monitoring site performance and to deliver interest based content.

Accept & Close

See privacy notice