SparkFun gator:soil - micro:bit Accessory Board

7.17€ 8.68€ VAT included
Rated 0/5 (0 Votes!)
Model: SPRKC-SEN-15272
Manufacturer: Sparkfun
Sparkfun

If your plants could talk, would they call out "Water me, Seymour?" Unfortunately (or fortunately, perhaps) plants have yet to develop the ability to speak. But thanks to the SparkFun gator:soil micro:bit Accessory Board, you can now measure the moisture level in soil without any vocal clamoring from your leafy lads. And, best of all--it is part of SparkFun's gator:bit series of alligator-clippable accessories, meaning you can easily interface it with the micro:bit or other microcontrollers!

The gator:soil consists of two probes and three pads (PWR, GND, and SIG). The probes are used to measure the conductivity of the soil. SIG provides an analog voltage out that can be attached to an ADC pad on the gator:bit (v2). The value read on SIG is dependent on a few variable, including soil composition, contact on the probes, soil compaction, and other factors. In most cases, it will behoove you to calibrate your sensor reading for each soil sample and sensor. Once calibrated, for a fixed sensor, the primary variables to measuring conductivity in the soil will be the power input and moisture content of the soil.

We recommend powering the gator:soil with between 3.3V - 5V. Again, please note that the analog value returned will vary depending on what voltage is provided for the sensor. For use with the gator:bit (v2) and micro:bit, you should provide 3.3V through the PWR and GND pads. We recommend not powering the sensor constantly to reduce corrosion of the probes; this can be controlled through one of the digital pins of the gator:bit (v2).


The micro:bit is a pocket-sized computer that lets you get creative with digital technology. Between the micro:bit and our shield-like bit boards you can do almost anything while coding, customizing and controlling your micro:bit from almost anywhere! You can use your micro:bit for all sorts of unique creations, from robots to musical instruments and more. At half the size of a credit card, this versatile board has vast potential!


Features:

  • gator:bit Compatible
  • Contacts:
    • PWR: INPUT: Power to the sensor (3.3V-5V)
    • SIG: OUTPUT: Analog voltage representing conductivity between probes
    • GND: REFERENCE: Ground reference (0V)
    • Probes: Used to sample soil moisture content for sensor

Documents:

Videos

For more information, please visit this products webpage.
More products in this category:

Buy Sparkfun On Demand »

More Featured Products
12.33€
Infrared Proximity Sensor Sharp GP2Y0A21YK
Infrared proximity sensor made by Sharp. Part # GP2Y0A21YK has an analog output that varies from 3.1V at 10cm to 0.4V at 80cm. The sensor has a Japanese Solderless Terminal (JST) Connector. We recommend purchasing the related pigtail below ...
9.70€
NodeMCU V3 IOT ESP8266 development kit
The NodeMcu is an open-source firmware and development kit that helps you to Prototype your IOT product within a few Lua script lines. Features: Open-source Interactive Programmable Low ...
5.75€
LilyPad Coin Cell Battery Holder - Switched - 20mm
Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you’ve even sewn a LilyPad slide switch in-line. Wouldn’t it be ...
2.23€
Breadboard White Self-Adhesive
Dimensions: 8.2x5.5cm Self-adhesive on the ...
5.49€
Pressure-Sensitive Conductive Sheet (Velostat/Linqstat)
This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit. It's pressure-sensitive: squeezing it will reduce the resistance, so it's handy for making flexible sensors. ...
4.96€
Europe Official Distributor
Adafruit
Pololu
Sparkfun
Makey makey
Lilypad
Arduino

Electan uses cookies for the operation of the website, monitoring site performance and to deliver interest based content.

Accept & Close

See privacy notice