SparkFun Lumenati 90R

6.51 7.88€ VAT included
Rated 0/5 (0 Votes!)
Model: SPRKC-COM-14358
Manufacturer: Sparkfun
Sparkfun

The SparkFun Lumenati 90R is a small quarter-circle board equipped with three APA102C LEDs and a single mounting position that has been designed to give your projects an edge in their lighting capacity. The 90R board has been specifically designed to be daisy-chained with other Lumenati boards, thanks to the castellated edge connectors at each end allowing for multiple design options and formations. Additionally, we have labeled the APA102C LEDs on each board with numbers indicating their position in the sequence to help you write code more easily. We especially love using the Lumenati boards to give our flying race drones a bit of style and panache.

The Lumenati 90R gets its name from the 90° angle it takes and the direction the signal and power flow. Combining four of the 90R boards creates a 12-LED ring with enough space in the center for a Lumenati 8-pack board. If you want to create more than just a small ring, you can also solder on 8-stick boards to the 90R to create outlines of different shapes and sizes.

The APA102C addressable LEDs operate on +5V power input, as well as 0--5V logic levels for clock and data, and employ a 2-wire communication protocol consisting of a clock line and a data line. While this requires one more wire than standard WS2812B LEDs, the advantage is that the communication with the LEDs becomes somewhat timing-independent, allowing you to run these directly off of a Raspberry Pi or other single-board computer that doesn?t normally allow for a long, precisely timed data stream without the use of additional hardware.

Note: There are two solder jumpers on the back of the 90R labeled CO and DO (clock out and data out) that can be cut to interrupt those signals in case you make a closed-loop design where you don?t want the clock and data from your last LED to interfere with the clock and data to your first. It is critical that you cut the traces in the jumpers of the last board in the loop before you power up your LEDs if you?ve put together a continuous loop of Lumenati boards. Otherwise, it is likely that you?ll burn out a couple of LEDs.

Features:

  • Dimensions: 35.7mm x 17.7mm x 3.2mm (1.4" x 0.7" x 0.12")
  • Weight: 1.4g

Documents:

Videos

For more information, please visit this products webpage.
More products in this category:

Buy Sparkfun On Demand »

More Featured Products
Makey Makey Classic Original Kit
Makes STEM Education fun! Start out easy with a banana piano. First setup takes seconds. Then make game controllers, musical instruments, and countless inventions. Advance to additional inputs and multi-key remapping up to 18 ...
49.50€ 39.75€
Flex Sensor Sparkfun
A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of ...
7.95€
Breadboard White Self-Adhesive
Dimensions: 8.2x5.5cm Self-adhesive on the ...
5.49€
Triple Axis Accelerometer and Gyro Breakout MPU6050A
The MPU-6050A combine a 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor (DMP) Features: -I2C Digital-output of 6 or 9-axis MotionFusion data in rotation ...
6.25€
Lithium Ion polymer Batteries 6A
This is a light weight, high energy density Lithium Ion polymer battery. It outputs a nominal 3.7v at 6000mAh, comes terminated with a standard 2-pin JST connector- 2mm spacing between pins. Features: Excellent long-term ...
22.95€
Circuit Playground Express - Base Kit
It's the Circuit Playground Express Base Kit! It provides the few things you'll need to get started with the new Circuit Playground Express. This version of Circuit ...
32.80€
Europe Official Distributor
Adafruit
Pololu
Sparkfun
Makey makey
Lilypad
Arduino

Electan uses cookies for the operation of the website, monitoring site performance and to deliver interest based content.

Accept & Close

See privacy notice