Pimoroni GFX HAT - 128x64 LCD Display

33.27 40.26€ VAT included
Rated 0/5 (0 Votes!)
Model: ADFC-3935
Manufacturer: Adafruit
Adafruit

Pimoroni's GFX HAT is a shiny new LCD Display with RGB Backlight and Touch Buttons! This is a seriously snazzy LCD that can display complex graphics for all your headless Pi games and animations. While the LCD is monochrome 128x64 pixels, the backlight can be set to different RGB colors to indicate

You also get six capacitive touch buttons for input and navigation, so you can use this as a controller too. The cool capacitive touch backlight colors are super soothing to tap on and off, and help you know that the touch was registered.

To top it all off, this HAT comes fully assembled with Python support to get you up and running, and since it's from Pimoroni you know it's going to look great on your next Raspberry Pi project.

Features:

  • 128x64 pixel, 2.15" LCD display
  • Integrated diffuser/reflector assembly
  • Six-zone RGB LED backlight
  • SN3218 LED driver chip (I2C address 0x54)
  • Six capacitive touch buttons with white LEDs
  • Microchip CAP1166 capacitive touch/LED driver chip (I2C address 0x2c)
  • Compatible with Raspberry Pi 3 B+, 3, 2, B+, A+, Zero, and Zero W
  • Python library
  • Comes fully assembled, plug and play right onto your Raspberry Pi

For more information, please visit this products webpage.
More products in this category:

Buy Adafruit Europe Official Distributor »

More Featured Products
Force Sensitive Resistor Round
This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no ...
6.10€
Alligator Clip Test Cables 10 Units
These are standard alligator to alligator (crocodile) clip test cables. The alligator clip allow you attach the test point without hold the cables which is really handy. The clip is strong and grippy. Length: ...
4.35€
40 Pin Male-Female Splittable Jumper Wire 200mm
This is a splittable 40 pin 200mm length jumper wire for ...
3.34€
Conductive Thread Bobbin - 12m (Smooth, Stainless Steel)
This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the ...
5.14€
Electric Heating Pad - 10cm x 5cm
This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand, it's just a gigantic resistor. On the other hand, it's flexible, light, and can be ...
5.44€
Adafruit WINC1500 WiFi Shield with PCB Antenna
Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support ...
27.33€
Teensy 4.0
Teensy 4.0 is the latest Teensy, offering the fastest microcontroller and powerful peripherals in the Teensy 1.4 by 0.7 inch form factor. It features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest ...
23.79€
Europe Official Distributor
Adafruit
Pololu
Sparkfun
Makey makey
Lilypad
Arduino

Electan uses cookies for the operation of the website, monitoring site performance and to deliver interest based content.

Accept & Close

See privacy notice