Adafruit Pi Protector for Raspberry Pi Model B+ / Pi 2

9.02€ 4.51 5.46€ VAT included
Rated 0/5 (0 Votes!)
Model: ADF-2292
Manufacturer: Adafruit
Adafruit
In Stock Available for immediate delivery

You've seen the A+ pocket protector - cometh the hour for the B+ / Pi 2 version. Introducing PaintYourDragon's last-cut masterpiece part ii: Adafruit Pi Protector for Raspberry Pi Model B+ / Pi 2! It's not quite a full case, however it will keep your Pi B+ safe and svelte.

Keep your Raspberry Pi® Model B+ computer tidy and safe in this lovely clear acrylic enclosure. We designed this  simple protector to be beautiful, easy to assemble and perfect for any use (but especially for those who want to carry their Pi around in their pocket!) This enclosure is only compatible with the Raspberry Pi Model B+ / Pi 2

Click here for the A+ version.

The case is as minimal it gets coming in just two pieces of acrylic that secure with six screws. Made of crystal-clear acrylic, this case keeps the Pi secure. You can use all of the connectors on the edges of the Pi: HDMI, Audio/Video, microSD slot, micro USB power, and the four USB ports. There's also a cut out to allow a 40-pin IDC cable to the GPIO breakout pins on the Pi.
 

Be sure to check out more of our awesome Raspberry Pi accessories including:

 

This product comes with the 2 acrylic pieces and assembly hardware. Raspberry Pi B+ computer is **not** included. No other cables or connectors or accessories are included.

 


 

For more information, please visit this products webpage.
More products in this category:
Customers who bought this product also purchased
Raspberry Pi 3 Model B+ 2018 WiFi Bluetooth
New RaspberryPi 3 Model B+ 2018 with ARM11 Cortex-A53 64-bit 1,4 GHz This board have the same form factor as Raspberry Pi Model B+. - ARM 11 Cortex-A53 64 bits 1,4 GHz BCM2837 - 1GB LPDDR2 SDRAM - WiFi 802.11 ...
46.95€
11.75€
Lithium Ion polymer Battery 1A
This is a light weight, high energy density Lithium Ion polymer battery. It outputs a nominal 3.7v at 1000mAh, comes terminated with a standard 2-pin JST connector- 2mm spacing between pins. Features: Excellent ...
9.45€
Resistor Pack 1/4W 25 each of 20 Values
1/4th Watt, +/- 5% tolerance carbon film PTH resistors. Comes with 25 of each value: 0Ω, 1.5Ω, 4.7Ω, 10Ω, 47Ω 110Ω, 220Ω, 330Ω, 470Ω, 680Ω 1kΩ, 2.2kΩ, ...
9.15€
SparkFun LiPo Charger Basic Micro-USB
If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells at a rate of 500mA. It ...
6.95€
Breadboard Clear 830 Tie In Points
Dimensions: 165 x 55 x 8.5mm. Self-adhesive on the ...
6.14€
Grove I2C Hub
I2C Hub Grove is an extension Grove module for connecting multiply I2C devices to Grove Base ...
4.39€ 3.07€
Round Solar Panel Skill Badge - 5V / 40mA
This skill badge is self-fulfilling! Normally you would get the badge after the project is done, but in this case, the badge can be part of the project! The solar panel is epoxied into a round disc 55mm diameter (about 2.2 ...
3.88€
Europe Official Distributor
Adafruit
Pololu
Sparkfun
Makey makey
Lilypad
Arduino

Electan uses cookies for the operation of the website, monitoring site performance and to deliver interest based content.

Accept & Close

See privacy notice