Adafruit

Displaying 1 to 68 (of 68 products)
VAT not included
2.90
These pretty strips of light are plastic diffused backlights, often seen in LCD displays. Normally they're tucked behind the LCD and ...
3.89
This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit. It's ...
7.82
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes ...
ADF-261
0.74
Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly charger!
24.05
The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have ...
12.02
Round and round and round they go! 16 ultra bright smart LED NeoPixels are arranged in a circle with 1.75" (44.5mm) outer diameter. The ...
2.90
What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light ...
1.92
These pretty strips of light are plastic diffused backlights, often seen in LCD displays. Normally they're tucked behind the LCD and ...
7.21
Make your own little LED strip arrangement with this stick of NeoPixel LEDs. We crammed 8 of the tiny 5050 (5mm x 5mm) smart RGB LEDs ...
9.57
Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, ...
14.71
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to ...
24.05
Here's a handy Arduino shield: we've had a lot of people looking for a dedicated and well-designed data logging shield. We worked hard ...
7.38
What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light ...
34.39
If you've ever ordered and wire up a 9-DOF sensor, chances are you've also realized the challenge of turning the sensor data from an ...
8.59
This is the half-sized Raspberry Pi Perma-Proto Breadboard from Adafruit, a simple solder-able-type bare PCB kit that affords you with ...
4.43
Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better ...
5.96
Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT ...
9.02€ 4.96
You've seen the A+ pocket protector - cometh the hour for the B+ / Pi 2 version. Introducing PaintYourDragon's last-cut masterpiece part ...
3.75
Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps ...
4.87
Polyimide Tape (sometimes referred to by the brand name Kapton Tape) is an interesting addition to your
23.45
"You see, wire telegraph is a kind of a very, very long cat.  You pull his tail in New York and his head is meowing in Los Angeles.  ...
3.89
Squeeze once to turn on, squeeze again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch ...
36.07
Add a good quality, slim chiclet keyboard as well as a optical mouse to your Raspberry Pi, Beagle Bone Black or other mini-computer with ...
42.90
New! Version 3 comes with the latest module which has external antenna support and Pulse-Per-Second output We carry
2.71
Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout ...
2.46
This 4" / 100mm long flexible uFL 2.4GHz antenna has approx 4DBi gain and a 50Ω impedance so it will work fantastic
5.96
Complete your Pi setup with our custom designed faceplate specifically designed to fit your 2.8" PiTFT and Adafruit Pi B+ / Pi 2 case ...
6.01€ 3.31
Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding COLORS!
29.47
It's the Circuit Playground Express Base Kit! It provides the few things you'll need to get started with the new
2.46
Outdoor enthusiasts rejoice! We now have standard 5.5/2.1mm DC power cable sets in a waterproof variety. These cable sets are ideal for ...
18.04
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The MAX31855K does everything for you, ...
1.48
Simple but effective - this breakout board has a USB Micro-B connector, with all 5 pins broken out. Great for pairing with a ...
6.01
The Raspberry Pi has an on-board audio jack, which is super handy for all kinds of sound effects and speech, just plug and go! However, ...
0.49
Oh say can you see By the knob's early light...
4.87
Do you ever find yourself saying, "Gee whiz I wish I could plug in 4 more USB devices to my tablet, or microcontroller with USB host, or ...
11.69
"You see, wire telegraph is a kind of a very, very long cat.  You pull his tail in New York and his head is meowing in Los Angeles.  ...
4.87
This handy Ethernet extension cable will make it easy for you to enclose a device that has an Ethernet port. We think this would be most ...
42.08
Put on your sunglasses before wiring up this LED matrix - 64 eye-blistering RGB LEDs adorn the NeoMatrix for a blast of configurable color. ...
2.46
This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a ...
1.99
If you've started designing your own PCBs in Eagle or
42.03
Is this not the cutest little display for the Raspberry Pi? It features a 2.8" display with 320x240 16-bit color pixels and a ...
24.55
Circuit Playground Express is the next step towards a perfect introduction to electronics and programming. We've taken t
1.92
Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our ...
54.06
Add some sizzle to your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection and a ...
0.49
Oh say can you see By the knob's early light...
1.92
When you need a lot of options, you need a Mini 8-Way Rotary Selector Switch. This is basically a single-pole t
21.04€ 11.57
By popular demand! We now have a way to attach a Raspberry Pi computer to a plastic 'dish' with a full-sized breadboard. We designed it ...
2.90
This adorable little board will come in very handy whenever you need a small amount of 5V power. It's the size of a linear regulator, ...
14.71
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. ...
42.03
Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display ...
1.48
A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates ...
1.99
If you've started designing your own PCBs in Eagle or
54.06
Is this not the cutest, little display for the Raspberry Pi? It features a 3.5" display with 480x320 16-bit color pixels
1.92
These magnetic pin backs have two pieces: a metal bar with adhesive strip and a plastic piece with two strong rare-earth magnets. Affix ...
21.04
These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of ...
4.87
When Bunnie showed up at Adafruit with the prototype for his Chibitronics Circuit Stickers we were
8.37
Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little ...
18.04
For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit ...
3.44
Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch ...
21.20
PowerBoost 1000C is the perfect power supply for your portable project! With a built-in load-sharing battery charger circuit, ...
3.61€ 1.99
Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding COLORS!
1.92
This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 are the most ...
4.04
This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. ...
19.65
Round and round and round they go! 24 ultra bright smart LED NeoPixels are arranged in a circle with 2.6" (66mm) outer diameter. The ...
9.02
Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit ...
7.38
Help! This patient is heating up! Is the voltage too low? Is the current draw too high? Is there a doctor in the house? Oh, thank ...
24.05
This new Adafruit Pi Plate makes it easy to use a blue and white 16x2 Character LCD. We re
0.93
Round and round it goes, this nice round "scrubber" knob is the perfect mate to a rotary encoder.  It's got a wide 34.7mm diameter with ...

Electan uses cookies for the operation of the website, monitoring site performance and to deliver interest based content.

Accept & Close

See privacy notice